TEL: +86 13120555503

Galician

Telephone: +86 13120555503

  • shar_1
  • shar_2
  • shar_3
  • shar_4
  • shar_5

Xul . 03, 2024 09:25 Back to list

A COMPLETE GUIDE TO PUMPING SLURRIES



A COMPLETE GUIDE TO PUMPING SLURRIES

Slurries are specialized compounds found in many processing industries, including sanitary industries such as food, dairy, beverage processing, and biopharmaceutical manufacturing. Slurries combine properties of both liquids and solids, and so specialized consideration must be given when it comes to determining the type and size of slurry pump to use with them.

This article will focus on:

  • Defining what slurries are
  • The types of pumps that may be used to pump slurries
  • Factors to consider when selecting a slurry pump for a particular application
  • A brief overview of a few of the sanitary processing pumps available from CSI suitable for pumping these unique compounds
<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

WHAT ARE SLURRIES?

Slurries are mixtures of solids and liquids, with the liquid serving as the transport mechanism used to move the solid. The size of the particles (or solids) in slurries ranges from one micron in diameter up to hundreds of millimeters in diameter. The particle size significantly impacts a pump's ability to move a slurry through a process line.

All slurries share five essential characteristics:

  1. More abrasive than pure liquids.
  2. Thicker in consistency than pure liquids.
  3. May contain a high number of solids (measured as a percentage of the total volume).
  4. The solid particles usually settle out of the slurry's precipitate relatively quickly when not in motion (depending on the particle size).
  5. Slurries require more energy to move than do pure liquids.

Slurries are further classified by industry into four classes based on how aggressive they are — Class 1 being the least aggressive and Class 4 the most aggressive. The pumping of slurries can have the following wear impacts on both pumps and pipeline components:

  • Abrasions: including gouging, high-stress grinding, and low-stress grinding (applicable only with settling-type slurries).
  • Erosion: the loss of surface materials caused by the action of the particles in the slurry being pumped. Erosion is primarily found with the pumping of settling-type slurries.
  • Corrosion: caused by the electrical galvanic action in the fluid being pumped. Certain types of slurries (e.g., highly acidic or alkaline compounds) will have more impact on component corrosion than will more benign slurries.

TYPES OF SLURRY PUMPS

As described below, there are several types of pumps that are suitable for pumping slurries. However, we must address a couple of critical considerations before considering which technology to use.

  1. The size and nature of the solids in the liquid: the size and nature will affect the amount of physical wear on the pump and its components and if the solids will pass through the pump without being damaged.

    A concern for centrifugal pumps is the speed and shear inside the pump may damage the slurry/solids. In general, twin screw pumps allow for the least damage to solids in a slurry.

  2. The corrosiveness of the liquid or slurry mixture: more corrosive slurries will wear pump components more quickly and may dictate the selection of the material from which the pump is constructed.
<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>
Alfa Laval LKH Series Centrifugal Pump
Pumps designed for pumping slurries will be heavier duty than those designed for less viscous liquids since slurries are heavy and difficult to pump.

Slurry pumps are typically larger in size than standard pumps, with more horsepower, and built with more rugged bearings and shafts. The most common type of slurry pump is the centrifugal pump. These pumps use a rotating impeller to move the slurry, similar to how a water-like liquid would move through a standard centrifugal pump.

Centrifugal pumps optimized for slurry pumping will generally feature the following in comparison to standard centrifugal pumps:

  • Larger impellers made with more material. This is to compensate for wear caused by abrasive slurries.
  • Fewer, thicker vanes on the impeller. This allows the passage of solids more readily — typically 2-5 vanes, compared to 5-9 vanes on a standard centrifugal pump.

For pumping abrasive slurries, these types of pumps may also be made from specialized high wear alloys such as AL-6XN® or Hastelloy® C-22®. Hardening stainless steel is also a common option for abrasive slurries, with Expanite and Armoly being two hardening processes.

For certain types of slurry pumping conditions, positive displacement pumps may be a more appropriate choice than a centrifugal-style pump.

ZJW Abrasion Resistant Feed Slurry Pump

<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

These conditions include:

  • A low slurry flow rate
  • A high head (i.e., the height to which the pump can move liquid)
  • A desire for greater efficiency than that afforded by centrifugal pumps
  • Improved flow control

Common types of positive displacement pumps used in slurry pumping applications include:

<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

ROTARY LOBE PUMPS

These pumps use two meshing lobes rotating within a pump's housing to move fluids from the pump's inlet to its outlet.

<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

TWIN-SCREW PUMPS

These pumps employ rotating screws to move liquids and solids from one end of the pump to another. The screws' turning action creates a spinning motion that pumps material.

<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

DIAPHRAGM PUMPS

These pumps use a flexible membrane that expands the volume of the pumping chamber, bringing in fluid from an inlet valve and then discharging it through an outlet valve.

 

SELECTING AND OPERATING A SLURRY PUMP

Choosing the right pump for your slurry application can be a complex task due to the balance of many factors including flow, pressure, viscosity, abrasiveness, particle size, and particle type. An applications engineer, who knows how to take all of these factors into account, can be a great help in navigating the many pump options available.

In determining which type of slurry pump is best suited for your particular application, follow these four simple steps.

<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

STEP 1

DETERMINE THE NATURE OF THE MATERIALS BEING PUMPED

Consider the following:

  • The particle size, shape, and hardness (impacts on the likelihood for abrasion and corrosion of the pump's components)
  • The corrosiveness of the slurry solution
  • If the exact in-pump viscosity of the product is unknown, CSI can help
<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

STEP 2

CONSIDER THE PUMP'S COMPONENTS

If it's a centrifugal pump, is the design of and material used to construct the impeller appropriate for pumping slurries?

  • What is the material used to construct the pump constructed? Higher alloys such as AL-6XN or Hastelloy C-22 are best for pumping highly abrasive slurries.
  • Are the pump's discharge components appropriate for the slurry to be pumped?
  • What is the best sealing arrangement for the application?
  • Will the solid size pass through the pump?
  • How much damage to the solid can the customer tolerate?

It's also important to consider the chemical compatibility of the slurry with any elastomers in the pump. Once one has addressed both the nature of the slurry and the components of different types of pumps, you may select the potential candidate slurry pump for the application.

<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

STEP 3

DETERMINE WHAT SIZE THE PUMP SHOULD BE

The most important thing here is figuring out the pump horsepower needed to deliver a specific fluid flow rate at the desired or required differential pressure. Look at the following:

  • The concentration of solids in the slurry — measured as a percentage of the total volume.
  • The length of the pipeline. The longer the pipeline, the greater the slurry-induced friction that will need to be overcome by the pump.
  • The slurry pipe diameter.
  • The static head — i.e., the height to which the slurry must be lifted in the piping system.
<trp-post-container data-trp-post-id='6820'>A COMPLETE GUIDE TO PUMPING SLURRIES</trp-post-container>

STEP 4

DETERMINE THE PUMP'S OPERATING PARAMETERS.

To reduce component wear, most centrifugal slurry pumps run at fairly low speeds — typically less than 1200 rpm. Find the sweet spot that allows the pump to run as slowly as possible but fast enough to prevent solids from settling out of the slurry precipitate and clogging the lines.

Then, lower the pump's discharge pressure to the lowest point possible to further reduce wear. And follow proper piping layout and design principles to ensure constant and uniform delivery of the slurry to the pump.

Share

Next：

Latest news
Hit enter to search or ESC to close